![delta unisaw weight delta unisaw weight](https://s3.amazonaws.com/vs-lumberjocks.com/o6xvi7b.jpg)
You can use the same trick loading cabinets/etc into a truck - get them close, tip them in, and lift up the on-ground portion and slide the cabinet in. I got it close to the back of my trailer, then tipped it over so the trailer was supporting the table from the top, then picked up the legs and flopped it into the trailer, upside down. DELTA MODEL 36-944 UNISAW HEAVY DUTY 10 TABLE SAW 3HP, 220 VOLT, 1-PHASE MACHINE BIESEMEYER FENCE SYSTEM WITH. If no other option existed it could work.I did the same to load my welding table- 390 Lbs of 3/4" steel plate with legs. I am not sure I would try this routine with a cabinet saw, and certainly not without help in the bed to control the tip. If no other option existed it could work. I am not sure I would try this routine with a cabinet saw, and certanly not without help in the bed to control the tip. Its also very stable for transport because all the heavy parts are low. The fence needs to be off and the blade should be down. Delta farmed out their casting work and some shops added additional identifying marks to the part number. Those parts started with LTA-800 and are not to be confused with Unisaw parts. The tail gate caries over haft the weight and one man can load it. Please note that later in time Delta briefly used the LTA parts prefix for their 10 Tilting Arbor Bench Saw (contractor’s saw). This practice was common with all Delta machines. 1471 Guard) Additional casting prefixes will be found on saw parts that were borrowed from other machines like the die cast dome knobs (NCS-prefix). Then they grab the legs and flip it over. Parts for the Unisaw began with LTA-401 (Table) and ended with LTA-552 (Coil Spring For No. Lift the front and rear sides of the loop to create a 4 point sling that catches under both extention tables and lifts from the center.Ĭontractors routinely load table saws in pick up beds by placing the edge of the table next to the tail gate and tilting the saw towards the tail gate. To lift my HD delta shaper or Unisaws, I put a loop type strap around the saw. Other than removing large extention tables, fences and lose accessories I would not disassembe to load. Use lifting grade hardware and over size it, because you will probably leave it in place to use again. Even an eye bolt through the headder of a garage door opening will work well. Delta has had excellent results with the totally enclosed, fan-cooled (TEFC) electric motors made by Marathon Electric in Missouri. Extention tables and other options will add up fast.Ī small chain fall or block and tackle will lift it easily if you have an A frame or exposed rafter and enough fly space. Secondly, is Delta unisaw still made in USA Delta decided at the outset that the new Unisaw, would be made in the USA at their Jackson, Tennessee facility and they strived to maintain this.
![delta unisaw weight delta unisaw weight](https://images.ctfassets.net/hnrwk8wffcvh/gUfcdS7LnamUEWy6iG6QA/a6c7c52154b227c94a8c8311919a7983/36-L352_F13_large.png)
Weight will vary depending on choice of extention table (some had very large cast iron extention tables, althought they are uncommon)ģ or 4 men should be able to lift a basic saw into the bed of a pick up. BIESEMEYER fence system has a powerful 3 horsepower, 230-Volt, 60 Hz American Marathon motor. Its a litte big to man handle easily, but small enough you dont want to drag out the rigging gear.
![delta unisaw weight delta unisaw weight](https://images-na.ssl-images-amazon.com/images/I/51IhDT66r-L._AC_UL160_SR160,160_.jpg)
The most common size of blade is 10" in diameter with a blade arbor diameter of ? 5⁄ 8", but 12" or 14" in diameter with a blade arbor diameter of 1" are found in commercial/industrial sites.66 is a good saw, but not all that heavy by my standards, but a size I hate. For most applications, the 1 1/2 or 2 horsepower motor on the contractor saw is powerful enough.ġ3⁄ 16" wide stacked dado blade in addition to a standard saw blade. Cabinet saws, on the other hand, generally have between 3 and 5 horsepower motors in them. Motor size: Most contractor table saws have either a 1 1/2 or 2 horsepower motor. Likewise, people ask, how much horsepower do you need for a table saw? Similarly, how much does a unisaw weigh? 3-HP Motor 10" UNISAW® with 52" BIESEMEYER® Fence System Weight: 661 lbs. Stationary table saws have a wide range of weights from 245 pounds to over fifteen hundred pounds.īeside this, how much does a Craftsman table saw weigh?
#Delta unisaw weight portable#
So, how much does a table saw weigh? The average weight of a portable job site table saw is about 69 pounds with the lightest hovering around 45 pounds and the heaviest reaching 100 pounds or more.